Panasonic NR-B32FW3 Service Manual Download | Manualshive

Page: 17 / 52

background image

17

6 Location of Controls and Components

6.1.

Display and Control Panel

Notes:

• Normally the panel displays are off. Displays appear when the buttons are operated, or the doors are opened.
• The displayed temperature may differ from the actual temperature.
• This refrigerator uses a microprocessor to control the temperature.

The temperature inside the refrigerator varies depending on such factors as changes in the room temperature, the speed at
which the compressor is operating, how frequently the doors are opened and closed, and how much food is stored inside and
how it is stored.

«
...
15
16
17
18
19
...
»

Summary of Contents for NR-B32FW3





















































Reviews:

No comments

Related manuals for NR-B32FW3

Brand: Unique Pages: 43

Brand: U-Line Pages: 18

Brand: JUNO Pages: 12

Brand: UNITED Pages: 8

Brand: True Pages: 2

Brand: Scandomestic Pages: 23

randell DEEP WELL Series

Brand: Unified Brands Pages: 19

Brand: NEFF Pages: 30

Brand: Avanti Pages: 16

Brand: Hotpoint Pages: 16

Brand: German pool Pages: 28

Brand: Morris Pages: 18

Brand: Infiniton Pages: 36

Brand: Magic Chef Pages: 11

Brand: Landmark Pages: 32

Brand: GE Pages: 80

Brand: GE Pages: 56

Brand: Samsung Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands