Panasonic MJ-J176PWTC Page 14 Service Manual Download | Manualshive

Page: 14 / 20

background image

14

6.8.

Glass container and cutting blade

1. Remove the cover, then turn the glass container up-side-

down.

2. Secure the glass cup and turn the mounting ring counter-

clockwise.

3. The gasket (upper) can be removed.
4. Wrap the cutting blade with a cloth for protection and

secure it.

5. Turn the upper connector clockwise with long nose pliers.

Then the cutting blade, and upper connector can be
removed.

• The parts can be assembled by reversing the disassem-

bly procedure.

«
...
12
13
14
15
16
...
»

Summary of Contents for MJ-J176PWTC





















Reviews:

No comments

Related manuals for MJ-J176PWTC

Brand: Jata electro Pages: 20

Brand: Morphy Richards Pages: 12

Brand: Omega Pages: 116

Brand: Taurus Pages: 42

Brand: Telefunken Pages: 34

Brand: Zelmer Pages: 48

Brand: Hamilton Beach Pages: 32

Brand: MAGIMIX Pages: 64

Brand: Omega Pages: 12

Brand: SAC Pages: 7

Brand: croydon Pages: 2

Brand: Green Power Pages: 20

Brand: BRAYER Pages: 44

Brand: BRAYER Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands