manualshive.com logo in svg

Panasonic LX-TD500, Programming Manual, Page: 329 / 388

Share
Download
Panasonic LX-TD500 Programming Manual Download Page 329

Maintenance

Programming Guide

329

Parameter

Remote FDN

Default

1499

Value Range

Up to 4 digits consisting of 0-9

Description/Function

Specifies the FDN (Floating Directory Number) for Remote 
Administration.

Reference

• 1.2 System Administration (F/G)

– System Programming and Diagnosis with Personal 

Computer
• 3.4.3 Remote Administration (Remote Connection) (I/M)

Parameter

DN Refer

Default

—

Value Range

—

Description/Function

Displays the list of DNs/FDNs which are already assigned to the 
extensions / system resources.

Reference

None

Parameter

[Remote Connect Information] Dial Number

Default

Blank

Value Range

Up to 40 digits consisting of 0-9,   , #, F, P, S or "-" (hyphen)

Description/Function

Specifies the dial number that is sent from the modem (remote 
location). You can see this dial number in the Batch Processing 
mode.

Reference

• 3.4.3 Remote Administration (Remote Connection) (I/M)

Parameter

[Remote Connect Information] Comment

Default

Blank

Value Range

Up to 40 characters consisting of 0-9, A-Z, a-z or the following 
marks: ! # $ %     ( ) + , - / : ; < = > ? @ &.

Description/Function

Specifies the comment area such as company name. You can see 
this comment in the Batch Processing mode.

Reference

• 3.4.3 Remote Administration (Remote Connection) (I/M)

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments