Panasonic LX-TD500 Programming Manual Download Page 190 | Manualshive

Page: 190 / 388

background image

Group

190

Programming Guide

Parameter

[Operator Setting] Call Priority

Default

CO Call: 1, Intercept Routing: 2, Recall: 3, Extension Call: 4

Value Range

Priority 1-4

Description/Function

Specifies the answering priority of incoming calls to the Operator
Group by a type of call when more than one call is ringing at an
Operator extension.
(Assignable only when "Operator" is specified in "Group Type"
programming.)

Notes

•

If all extensions in the Operator group are busy, incoming
calls directed to the group will be put in the waiting queue in
order of precedence determined by this Call Priority setting.

•

If the same priority is set on all four types of calls, the calls
will be put in the waiting queue in order of the arrival.

Reference

• 1.3 System Features (F/G)

– Operator Group

• 1.6 Originating Features (F/G)

– Operator Call

Parameter

[Operator Setting] Ringing Type

Default

Single

Value Range

1.

Multi

2.

Single

Description/Function

Specifies whether the calls coming in on an Operator Group ring
one Operator (Single) or all Operators in the group (Multi)
simultaneously.
(Assignable only when "Operator" is specified in "Group Type"
programming.)

Reference

• 1.3 System Features (F/G)

– Operator Group

• 1.6 Originating Features (F/G)

– Operator Call

«
...
188
189
190
191
192
...
»

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments

Related manuals for LX-TD500

Brand: Yepp Pages: 10

Brand: Polaris Pages: 142

2005-2008 RX500 FA

Brand: Honda Pages: 540

Brand: Baja motorsports Pages: 82

Brand: Xxxlutz Pages: 58

GE-YX125 series

Brand: GMX Pages: 18

Brand: Eagle Pages: 53

Brand: GAS GAS Pages: 60

Brand: Yamaha Pages: 176

Brand: Yamaha Pages: 156

Brand: Suzuki Pages: 508

Brand: ParCar Pages: 114

Brand: Pongratz Pages: 11

Brand: KYMCO Pages: 171

Stampede 900 2017

Brand: Textron Pages: 237

Brand: TransTank Pages: 20

Brand: Polaris Pages: 135

Brand: Polaris Pages: 117

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands