Panasonic LX-TD500 Programming Manual Download Page 184

Page: 184 / 388

Group

184

Programming Guide

Parameter

FDN

Default

Blank

Value Range

3-4 digits consisting of 0-9

Description/Function

Specifies the FDN (Floating Directory Number) for the Incoming
Group.

Reference

• 1.3 System Features (F/G)

– Floating Station

Parameter

DN Refer

Default

—

Value Range

—

Description/Function

Displays the list of DNs/FDNs which are already assigned to the
extensions / system resources.

Reference

None

Parameter

Group Type

Default

DIL 1:N

Value Range

DIL 1:N

Terminate

Ring

Operator

UCD

Description/Function

Specifies the Group Type for each Incoming Group.
This determines how the Incoming Group handles the incoming
calls directed to it.

DIL 1:N:
Functions as a DIL 1:N Group.

Terminate:
Functions as a Station Hunting Group (Terminate).

Ring:
Functions as a Ring Group.

Operator:
Functions as an Operator Group.

UCD:
Functions as a UCD (Uniform Call Distribution) Group.

Reference

• 1.3 System Features (F/G)

– Incoming Group

Summary of Contents for LX-TD500





































































































































































































































































































































































































Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands

Panasonic LX-TD500, Programming Manual

Search results

Summary of Contents for LX-TD500

Reviews:

Related manuals for LX-TD500

Brands by name

Popular brands