manualshive.com logo in svg

Panasonic LX-TD500, Programming Manual, Page: 182 / 388

Share
Download
Panasonic LX-TD500 Programming Manual Download Page 182

Group

182

Programming Guide

(

= assignable)

*1

 When "DIL 1:N" is specified in "Group Type" programming of Incoming Group, this feature 

does not work.

Incoming Group Copy

Used to copy a part of or all settings of a certain Incoming Group to all other Incoming Groups 
at a time. You can also specify one or several Incoming Groups as the copy destination.

Copying the Incoming Group Parameters to Other Incoming Groups

1. Edit the parameters of the copy source Incoming Group and save it.

2. Point to 

 on "3-4 Incoming Group" screen of the copy source and click.

•

"Incoming Group Copy" screen is displayed.

•

The current Incoming Group (copy source) number is shown as "Copy from Incoming 
Group 1-96." 

Applicability of Group Types to Overflow Destinations

Group 

Type

Overflow Destination

DN

External

Pager

OGM

Group

Extension

Group

Phantom

Extension

RMT

Incoming

Group

Terminate

Operator

*1

UCD

*1

Summary of Contents for LX-TD500





































































































































































































































































































































































































Reviews:

No comments