Panasonic LST 116 Installation And Operating Instructions Manual Download Page 1 | Manualshive

Page: 1 / 36

Panasonic LST 116 Installation And Operating Instructions Manual Download Page 1

Installation and Operating Instructions

Video Intercom System — Lobby Station

Model No.

VL-VN1900

Thank you for purchasing a Panasonic product.
Please follow all instructions in this document and save it for future reference.
Carefully read the information found in the section titled "2.1 Important safety information" in particular.

This system is an auxiliary system; it is not designed to provide complete protection from property loss.
Panasonic will not be held responsible in the event that property loss occurs while this system is in operation.

Note to the installer

R

This document includes instructions for both installation and operation. See the section titled
"4 Installation" for installation instructions.

R

Please read this document carefully, and install the product safely and correctly by following the
instructions.

R

Only use attachments/accessories specified by the manufacturer.

R

The installation shall be carried out in accordance with all applicable installation rules.

1
2
3
...
»

Summary of Contents for LST 116





































Reviews:

No comments