manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 68 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 68

4.1  Web User Interface Setting List

The following tables show all the settings that you can configure from the Web user interface and the access
levels. For details about each setting, see the reference pages listed.
For details about setting up Web user interface programming, see 

1.1.5  Web User Interface

Programming

.

The settings that can be accessed may be limited by the configuration file programming.

Status

Menu Item

Section Title

Setting

Access

Level

*1

Ref.

U

A

Version
Information

Version Information

Model

ü

ü

Page 86

Operating Bank

ü

ü

Page 87

Firmware Version (Bank1)

ü

ü

Page 87

Firmware Version (Bank2)

ü

ü

Page 87

KEM1 Version

ü

ü

Page 87

KEM2 Version

ü

ü

Page 87

68

Administrator Guide

Document Version  2015-01  

4.1 Web User Interface Setting List

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments