manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 168 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 168

4.6.9  LDAP

This screen allows you to change the LDAP settings.

4.6.9.1  LDAP

Enable LDAP

Description

Specifies whether LDAP is enabled or disabled.

Value Range

•

Yes

•

No

Default Value

No

Configuration File Reference

LDAP_ENABLE (Page 284)

LDAP Server Address

Description

Specifies the address (in dotted-decimal notation or FQDN) used when
accessing the LDAP server.

Value Range

Max. 127 characters

Default Value

Not stored.

Configuration File Reference

LDAP_SERVER (Page 284)

LDAP Server Port

Description

Specifies the port used when accessing the LDAP server.

Value Range

1–65535

168

Administrator Guide

Document Version  2015-01  

4.6.9 LDAP

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments