manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 136 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 136

4.5.3.5  DTMF

DTMF Type

Description

Selects the method for transmitting DTMF (Dual Tone Multi-Frequency)
tones.

Value Range

•

Inband

•

RTP Event (2833)

•

None

Note

•

If you select RTP Event (2833), DTMF tones will be sent via
2833 event.

Default Value

RTP Event (2833)

Configuration File Reference

DTMF_MODE (Page 324)

DTMF Relay

Description

Specifies whether DTMF relay is enabled or disabled.

Value Range

•

Yes

•

No

Note

•

When set to "Yes", DTMF tones will be sent through SDP
regardless of the DTMF Type setting.

Default Value

No

Telephone-event Payload Type

Description

Specifies the RFC 2833 payload type for DTMF tones.

Value Range

96–127

Default Value

101

Configuration File Reference

TELEVENT_PAYLOAD (Page 324)

4.5.3.6  Call Hold

Supports RFC 2543 (c=0.0.0.0)

Description

Selects whether to enable the RFC 2543 Call Hold feature on this line.

136

Administrator Guide

Document Version  2015-01  

4.5.3 VoIP Settings [Line 1]–[Line n]

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments