manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 132 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 132

4.5.2  VoIP Settings

This screen allows you to change the VoIP settings that are common to all lines.

4.5.2.1  RTP Settings

RTP Packet Time

Description

Selects the interval, in milliseconds, between transmissions of RTP
packets.

Value Range

•

10

•

20

•

30

•

40

Default Value

20

Configuration File Reference

RTP_PTIME (Page 318)

Minimum RTP Port Number

Description

Specifies the lowest port number that the unit will use for RTP packets.

Value Range

1024–48750 (even number only)

Default Value

16000

Configuration File Reference

RTP_PORT_MIN (Page 317)

Maximum RTP Port Number

Description

Specifies the highest port number that the unit will use for RTP packets.

Value Range

1424–49150 (even number only)

132

Administrator Guide

Document Version  2015-01  

4.5.2 VoIP Settings

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments