manualshive.com logo in svg

Panasonic KX-UTG200, Setup Manual, Page: 112 / 412

Share
Download
Panasonic KX-UTG200 Setup Manual Download Page 112

Note

•

If the unit is connected directly to the Internet, you do not need to configure Global Address Detection.

4.3.8.1  STUN Server

STUN Server Address

Description

Specifies the IP address or FQDN of the STUN server.

Value Range

Max. 127 characters

Default Value

Not stored.

Configuration File Reference

STUN_SERV_ADDR (Page 283)

STUN Server Port

Description

Specifies the port number of the STUN server.

Value Range

1–65535

Default Value

3478

Configuration File Reference

STUN_SERV_PORT (Page 283)

STUN Interval

Description

Specifies the STUN interval in seconds.

Value Range

0, 10–86400 (0: Disable)

Default Value

0

Configuration File Reference

STUN_REFRESH_INTVL (Page 283)

112

Administrator Guide

Document Version  2015-01  

4.3.8 Global Address Detection

Summary of Contents for KX-UTG200





























































































































































































































































































































































































































Reviews:

No comments