Panasonic KX-UTG200 Administrator'S Manual Download

Page: 254 / 312

DSCP_RTP

Value Format

Integer

Description

Selects the DSCP level of DiffServ applied to RTP packets.

Value Range

0–63

Default Value

Web User Interface Reference

RTP Packet QoS (DSCP) (Page 114)

DSCP_RTCP

Value Format

Integer

Description

Selects the DSCP level of DiffServ applied to RTCP packets.

Value Range

0–63

Default Value

Web User Interface Reference

RTCP Packet QoS (DSCP) (Page 115)

RTCP_INTVL

Value Format

Integer

Description

Specifies the interval, in seconds, between RTCP packets.

Value Range

5–65535

Default Value

Web User Interface Reference

RTCP-XR (Page 115)

MAX_DELAY

Value Format

Integer

Description

Specifies the maximum delay, in 10-millisecond units, of the jitter buffer.

Value Range

3–50 (

10 ms)

Note

•

This setting is subject to the following conditions:

–

This value must be greater than "

NOM_DELAY

–

This value must be greater than "

MIN_DELAY

–

NOM_DELAY

" must be greater than or equal to

MIN_DELAY

Default Value

Web User Interface Reference

Maximum Delay (Page 115)

254

Administrator Guide

Document Version 2014-04

5.7.1 Per Line - VoIP

Summary of Contents for KX-UTG200

























































































































































































































































































































Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands

Panasonic KX-UTG200, Administrator'S Manual

Search results

Summary of Contents for KX-UTG200

Reviews:

Related manuals for KX-UTG200

Brands by name

Popular brands