Panasonic KX-UT670 Administrator'S Manual Download Page 95

Page: 95 / 250

Timer D

Description

Specifies the value of SIP timer D (wait time for answer resending), in
milliseconds. For details, refer to RFC 3261.

Value Range

0, 250–64000

Default Value

5000

Configuration File Reference

SIP_TIMER_D_n (Page 207)

Timer F

Description

Specifies the value of SIP timer F (non-INVITE transaction timeout
timer), in milliseconds. For details, refer to RFC 3261.

Value Range

250–64000

Default Value

32000

Configuration File Reference

SIP_TIMER_F_n (Page 208)

Timer H

Description

Specifies the value of SIP timer H (wait time for ACK reception), in
milliseconds. For details, refer to RFC 3261.

Value Range

250–64000

Default Value

32000

Configuration File Reference

SIP_TIMER_H_n (Page 208)

Timer J

Description

Specifies the value of SIP timer J (wait time for non-INVITE request
resending), in milliseconds. For details, refer to RFC 3261.

Value Range

0, 250–64000

Default Value

5000

Configuration File Reference

SIP_TIMER_J_n (Page 208)

4.6.2.10 Quality of Service (QoS)

SIP Packet QoS (DSCP)

Description

Selects the DSCP (Differentiated Services Code Point) level of DiffServ
applied to SIP packets.

Value Range

0–63

Document Version 2012-07

Administrator Guide

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands