Panasonic KX-UT670 Administrator'S Manual Download Page 90

Page: 90 / 250

Value Range

1–65535

Default Value

5060

Configuration File Reference

SIP_RGSTR_PORT_n (Page 192)

Proxy Server Address

Description

Specifies the IP address or FQDN of the SIP proxy server.

Value Range

Max. 127 characters

Default Value

Not stored.

Configuration File Reference

SIP_PRXY_ADDR_n (Page 191)

Proxy Server Port

Description

Specifies the port number to use for communication with the SIP proxy
server.

Value Range

1–65535

Default Value

5060

Configuration File Reference

SIP_PRXY_PORT_n (Page 191)

Presence Server Address

Description

Specifies the IP address or FQDN of the SIP presence server.

Value Range

Max. 127 characters

Default Value

Not stored.

Configuration File Reference

SIP_PRSNC_ADDR_n (Page 199)

Presence Server Port

Description

Specifies the port number to use for communication with the SIP
presence server.

Value Range

1–65535

Default Value

5060

Configuration File Reference

SIP_PRSNC_PORT_n (Page 199)

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands