Panasonic KX-UT670 Administrator'S Manual Download Page 66

Page: 66 / 250

4.3 Status

This section provides detailed descriptions about all the settings classified under the

[Status]

tab.

4.3.1 Version Information

This screen allows you to view the current version information such as the model number and the firmware
version of the unit.

4.3.1.1 Version Information

Model

Description

Indicates the model number of the unit (reference only).

OS Version

Description

Indicates the software version that is currently installed on the unit
(reference only).

Firmware Version

Description

Indicates the version of the firmware that is currently installed on the
unit (reference only).

4.3.2 Network Status

This screen allows you to view the current network information of the unit, such as the MAC address, IP
address, Ethernet port status, etc.

Administrator Guide

Document Version 2012-07

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands