Panasonic KX-UT670 Administrator'S Manual Download Page 117

Page: 117 / 250

4.7.3 Tone Settings

This screen allows you to configure the dual-tone frequencies and ringtone patterns of each tone.

4.7.3.1 Dial Tone

Tone Frequencies

Description

Specifies the dual-tone frequencies, in hertz, of dial tones using 2 whole
numbers separated by a comma.

Value Range

0, 200–2000 (0: No tone)

Note

•

If the value for this setting is "350,440", the unit will use a mixed
signal of a 350 Hz tone and a 440 Hz tone.

Default Value

350,440

Configuration File Reference

DIAL_TONE1_FRQ (Page 166)

Tone Timings

Description

Specifies the pattern, in milliseconds, of dial tones using up to 10 whole
numbers (off 1, on 1, off 2, on 2…) separated by commas.

Document Version 2012-07

Administrator Guide

117

Section 4 Web User Interface Programming

Summary of Contents for KX-UT670



























































































































































































































































Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands

Panasonic KX-UT670, Administrator'S Manual

Search results

Summary of Contents for KX-UT670

Reviews:

Related manuals for KX-UT670

Brands by name

Popular brands