Panasonic KX-TVM50 Programming Manual Download Page 142

Page: 142 / 200

2.6 Hardware (H/W) Settings

142

Programming Guide

Value Range

500 ms–20000 ms, Units 100 ms

Dial Start Mode

Specifies whether dialling starts after a dial tone is detected or after the time specified in "Off-hook
Delay" has passed.

Value Range

Dial Tone Mode, Delay Mode

Off-hook Delay

Specifies the length of time that passes before dialling starts. This setting is only needed when "Dial
Start Mode" is set to "Delay Mode".

Value Range

500 ms–20000 ms, Units 100 ms

Delay After Dialling Before On-hook

Specifies the length of time that the VPS waits for an answer when making an outside call. If no
answer is detected, the VPS disconnects the call.

Value Range

0 s–250 s

Record Start Beep Tone

Defines the beep tone that is heard when recording starts.

If "None" is selected, beep tones will not be heard.

Frequency

Specifies the frequency (pitch) of the beep tone.

Value Range

None, 400 Hz, 666 Hz, 1000 Hz, 1400 Hz, and 2000 Hz

Amplitude

Specifies the amplitude (volume) of the beep tone.

Value Range

-24–+6 dBm

Summary of Contents for KX-TVM50









































































































































































































Search results

Summary of Contents for KX-TVM50

Reviews:

Related manuals for KX-TVM50

Brands by name

Popular brands

Panasonic KX-TVM50, Programming Manual

Search results

Summary of Contents for KX-TVM50

Reviews:

Related manuals for KX-TVM50

Brands by name

Popular brands