manualshive.com logo in svg

Panasonic KX-TVM200, Installation Manual

Share
Download
Panasonic KX-TVM200 Installation Manual Download Page 190

6.1 Starting Up

190

Installation Manual

6.1

Starting Up

6.1.1

Before Programming

Careful preparation before you begin programming the VPS will make the programming and 
customisation process easier for you and the customer.

1.

Determine the customer's needs.

–

Work with the owner/supervisor and Message Manager to build the Custom Service 
Greetings, Holiday Greetings, etc.

–

Decide which ports/trunks should be answered by which greetings.

–

Confirm the software level of the PBX to make sure it is compatible with the features the 
customer wishes to use.

2.

While programming the VPS with KX-TVM Maintenance Console, make sure subscribers do not 
change any of their mailbox settings, otherwise programmed settings may not be saved properly.

3.

Work with the Message Manager (perhaps a receptionist or supervisor) to make sure he or she 
understands the system as well as his or her responsibilities as the Message Manager. This will 
save you time in the long run.

–

Show the Message Manager how to record system greetings. Refer to 3.2.6 Recording 
Messages in the Feature Manual.

–

Show the Message Manager how to transfer General Delivery Mailbox messages. Refer to 
3.2.2 Managing the General Delivery Mailbox in the Feature Manual.

6.1.2

Quick Setup

The Quick Setup utility allows you to set essential VPS parameters quickly and easily. It is particularly 
useful when configuring the VPS for the first time or after initialising the VPS.

The following settings can be programmed with the Quick Setup utility:

–

System Security settings

–

PBX Environment settings

–

Mailbox settings

–

Port/Trunk settings

–

Date and Time setting

Note

•

Set the desired parameters in each screen then click "Next" or "Back" to go to the desired 
screen.

•

Each screen of the Quick Setup utility must be completed in order for the settings to take 
effect.

•

The screen shots in this section are examples of the KX-TVM200.

•

Settings shown in the screen shots in this section are examples only and may vary 
depending on the type or settings of the connected PBX, the software version, etc.

Summary of Contents for KX-TVM200



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands