manualshive.com logo in svg

Panasonic KX-TVM200, Installation Manual

Share
Download
Panasonic KX-TVM200 Installation Manual Download Page 170

5.4 KX-TE Series PBX Programming for Inband Integration

170

Installation Manual

5.4

KX-TE Series PBX Programming for Inband 
Integration

The instructions in this section are for programming a KX-TE series PBX via the Operating and 
Maintenance Tool. To program a KX-TE series PBX using the Manager Extension, follow the 
instructions for KX-TA series PBX programming by referring to 5.7 KX-TA Series PBX Programming 
for Inband Integration.

1.

Go to the "1.System-2.Main" screen.

2.

Under "Voice Mail", select "DTMF Integration", then select each extension jack that is connected 
to the VPS. Click "Apply" to save the changed data.

3.

Go to the "2.Extension-6.Extension Group" screen.

4.

Put all extensions connected to the VPS into the same extension group. 

Reserve this extension group for these extensions! Do not mix other extensions into this 
group.

5.

Set the hunting type for the VPS extension groups to "Circular". Click "Apply" to save the changed 
data.

Summary of Contents for KX-TVM200



























































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands