manualshive.com logo in svg

Panasonic KX-TGP700, Administrator'S Manual

Share
Download
Panasonic KX-TGP700 Administrator'S Manual Download Page 295

DTMF_INTDIGIT_TIM

Value Format

INTEGER

Description

Specifies the interval, in milliseconds, between DTMF signals.

Value Range

60–200

Default Value

90

4.28  RTP/RTCP/RTCP-XR Settings

DSCP_RTP_n

For details about parameter names that include lower-case letters (e.g., "_n", "y", "x", or "m"), see
"4.2.1 Configuration File Parameters".

Value Format

INTEGER

Description

Specifies the DSCP level of DiffServ applied to RTP packets.

Value Range

0–63

Default Value

0

Web User Interface Reference

RTP Packet QoS (DSCP)

DSCP_RTCP_n

For details about parameter names that include lower-case letters (e.g., "_n", "y", "x", or "m"), see
"4.2.1 Configuration File Parameters".

Value Format

INTEGER

Description

Specifies the DSCP level of DiffServ applied to RTCP/RTCP-XR
packets.

Value Range

0–63

Default Value

0

Web User Interface Reference

RTCP Packet QoS (DSCP)

MAX_DELAY_n

For details about parameter names that include lower-case letters (e.g., "_n", "y", "x", or "m"), see
"4.2.1 Configuration File Parameters".

Value Format

INTEGER

Description

Specifies the maximum delay, in 10-millisecond units, of the jitter
buffer.

Value Range

3–50 (× 10 ms)

Note

•

This setting is subject to the following conditions:

–

This value must be greater than "

NOM_DELAY

"

–

This value must be greater than "

MIN_DELAY

"

Default Value

20

4.28 RTP/RTCP/RTCP-XR Settings

Document Version: 2020-04

Administrator Guide

295

Summary of Contents for KX-TGP700
















































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands