Panasonic KX-TGA680 Operating Instructions Manual Download | Manualshive

Page: 69 / 109

background image

Display message

Cause/solution

Use rechargeable battery.

R

A wrong type of battery such as Alkaline or
Manganese was inserted. Use only the rechargeable
Ni-MH batteries noted on page 4, 7.

Troubleshooting

If you still have difficulties after following the instructions in this section, disconnect the base unit’s
AC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,
and then insert the batteries into the handset again.

General use

Problem

Cause/solution

The handset does not turn on
even after installing charged
batteries.

R

Place the handset on the base unit or charger to turn on
the handset.

The unit does not work.

R

Make sure the batteries are installed correctly (page 11).

R

Fully charge the batteries (page 11).

R

Check the connections (page 10).

R

Unplug the base unit’s AC adaptor to reset the unit.
Reconnect the adaptor and try again.

R

The handset has not been registered to the base unit.
Register the handset (page 47).

I cannot pair a cellular phone to
the base unit.

R

Depending on the compatibility of the cellular phone, you
may not be able to pair it to the base unit. Confirm that
your cellular phone supports the hands-free profile (HFP)
specification.

R

Confirm that the Bluetooth feature of your cellular phone
is turned on. You may need to turn this feature on
depending on your cellular phone.

R

The Bluetooth technology on your cellular phone may not
be functioning normally. Turn off and on your cellular
phone.

R

If your cellular phone is already connected to another
Bluetooth device such as a Bluetooth headset, turn it off
or disconnect it from your cellular phone.

R

Some cellular phones may require you to enter the base
unit PIN to pairing. Confirm that you entered the correct
PIN.

For assistance, please visit http://www.panasonic.com/help

69

Useful Information

TG78xx(en)_1210_ver101.pdf 69

2012/12/10 21:19:31

«
...
67
68
69
70
71
...
»

Summary of Contents for KX-TGA680














































































































Reviews:

No comments

Related manuals for KX-TGA680

Brand: NSS Pages: 12

ST1000E with TRS

Brand: Sure Sweep Pages: 36

Brand: Duerkopp Adler Pages: 35

Brand: Sagem Pages: 104

Brand: MAGMATIC Pages: 20

Brand: COMAC Pages: 29

Brand: Pea Soup Pages: 2

Brand: Konica Minolta Pages: 92

Personal FAX-170

Brand: Brother Pages: 76

Brand: Brother Pages: 37

Brand: Brother Pages: 203

Brand: Brother Pages: 264

Brand: Brother Pages: 93

Brand: Brother Pages: 153

Brand: Brother Pages: 11

Brand: Toshiba Pages: 33

Brand: Toshiba Pages: 33

Brand: Toshiba Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands