Panasonic KX-TG6561BXT Page 35 Service Manual Download

Page: 35 / 90

KX-TG6561BXT/KX-TGA651BXT

9.1.6.

Check the RF part

9.1.6.1.

Finding out the Defective part

After All the Checkings or Repairing

1. Re-register the checked handset to the checked base unit, and Regular HS to Regular BU.

Note:

(*1) HS: Handset
(*2) BU: Base Unit

1. Prepare Regular HS(*1) and Regular BU(*2).
2. a. Re-register regular HS (Normal mode) to base unit (to be checked).

If this operation fails in some ways, the base unit is defective.
b. Re-register handset (to be checked) to regular BU (Normal mode).
If this operation fails in some ways, the handset is defective.

Base unit is defective

Handset is defective

START

Registration of

Regular HS to

base unit

Registration of

handset to

Regular BU

(other checkings)

Registration of handset to base unit

(checked ones)

Registration of Regular HS to Regular BU

Yes

Summary of Contents for KX-TG6561BXT



























































































Search results

Summary of Contents for KX-TG6561BXT

Reviews:

Related manuals for KX-TG6561BXT

Brands by name

Popular brands

Panasonic KX-TG6561BXT, Service Manual

Search results

Summary of Contents for KX-TG6561BXT

Reviews:

Related manuals for KX-TG6561BXT

Brands by name

Popular brands