Panasonic KX-TG4000B Page 97 Operating Instructions Manual Download

Page: 97 / 108

Chapter 5

Useful Information

With the cordless handset

Problem

The unit does not work.

“

No link to base.

Walk closer to

base & try again

” is

displayed and an alarm
tone sounds.

Static, sound cuts in/out,
fades. Interference from
other electrical units.

The unit does not ring.

You cannot dial.

The display is blank.

You cannot program
function items, such as the
line selection.

Remedy

•

Charge the battery fully (p. 16).

•

Clean the charge contacts and charge
again (p. 17).

•

Install the battery properly (p. 89).

•

Re-install the battery. Try again.

•

The handset has not been registered to the
base unit. Register the handset (p. 19, 52).

•

You are too far from the base unit.
Walk closer to the base unit and try again.

•

Raise the base unit antenna.

•

Locate the cordless handset and the base
unit away from other electrical appliances
(p. 4).

•

Walk closer to the base unit.

•

Raise the base unit antenna.

•

The ringer volume is set to OFF. Select
HIGH or LOW (p. 21).

•

If 4 other handsets or the base unit and 3
other handsets are in use, the unit may not
ring. Other handset users will hear
incoming call tones.

•

The handset is removed from the line group.
Add to the line group (p. 49).

•

The dialed number is restricted. To cancel,
see page 49.

•

Key lock mode is set. Cancel the mode by
pressing and holding

(FUNCTION)

•

Charge the battery fully (p. 16).

•

Programming is not possible while in the
talk or intercom mode, or while listening to
messages.

•

Do not pause for over 60 seconds while
programming.

•

Make sure that the handset is in the
standby mode.

Summary of Contents for KX-TG4000B













































































































Search results

Summary of Contents for KX-TG4000B

Reviews:

Related manuals for KX-TG4000B

Brands by name

Popular brands

Panasonic KX-TG4000B, Operating Instructions Manual

Search results

Summary of Contents for KX-TG4000B

Reviews:

Related manuals for KX-TG4000B

Brands by name

Popular brands