manualshive.com logo in svg

Panasonic KX-TES824, Features Manual

Share
Download
Panasonic KX-TES824 Features Manual Download Page 43

1.5 Making Call Features

Feature Guide

43

1.5.2.3

Account Code Entry

Description

An account code is used to identify outgoing outside (CO) line calls for accounting and billing purposes. 
Account codes are appended to SMDR call records (

 1.20.1 Station Message Detail Recording Feature), 

and have several uses. For example, a firm can use an account code for each client to determine which calls 
were made for which client, and can submit a bill to the client according to the client's account code as 
shown on the SMDR call record. 
There are 4 methods of entering account codes, explained below. One method is assigned to each 
extension through system programming (

 Account Code Mode [605]).

Conditions

•

An account code can be stored in Memory Dialling (One-touch Dialling, Hot Line, Speed Dialling—
System/Personal, Call Forwarding (FWD) to Outside (CO) Line, etc.). In this case, the Account Code 
feature number and specified account code must be entered after the Outside (CO) Line Access 
number.

•

An extension user does not need to enter an account code for incoming outside (CO) line calls.

•

Even in Forced/Verify-All/Verify-Toll mode, emergency calls can be made without an account code (

 

1.5.2.2 Emergency Call).

User Manual References

1.2.1 Basic Calling

Mode

Description

Option

An extension user can (but is not required to) enter a 4-digit account code 
during a conversation or within 30 seconds after a conversation ends 
when a record is needed.

Forced

An extension user must always enter a 4-digit account code within 5 
seconds after seizing an outside (CO) line. This method ensures that 
extension users will not forget to enter account codes.

Verify-All

An extension user must always enter a preprogrammed account code (

 

Account Code [310]) within 5 seconds after seizing an outside (CO) line. 
If the entered code does not match any preprogrammed code, the user 
will hear a reorder tone. 

Verify-Toll

An extension user can enter a preprogrammed account code (

 Account 

Code [310]) within 5 seconds after seizing an outside (CO) line to override 
TRS (

 1.8.2 Toll Restriction (TRS) Override by Account Code). Classes 

of service (COSs) 3 through 5 will be changed temporarily to COS 2. 
COSs 1 and 2 will not be affected. If the entered account code is also 
registered as an extension password, the extension password feature will 
be given priority. The COS of the corresponding extension will be applied.

Summary of Contents for KX-TES824











































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands