Panasonic KX-TDA15 Features Manual Download Page 402

Page: 402 / 420

3.1 Capacity of System Resources

402

Feature Guide

3.1

Capacity of System Resources

System

Dialling

Item

Capacity

Absent Message—Extension

1 x 16 characters

Absent Message—System

8 x 16 characters

Call Park Zone

100

Conference

3-8 parties per conference (32 parties total)

COS

DID/DDI Table

32 digits, 1000 entries

Extension number

1-5 digits (2-4 digits for extensions which have a VM

[DPT] mailbox)

Extension Personal Identification Number (PIN)

10 digits, 1 entry/extension

Host PBX Access Code

10 digits, 10 entries/trunk group

Multiple Subscriber Number (MSN)

10 entries per ISDN-BRI port

Number of Characters of Name

Printing message

Queuing Time Table

Ring Tone Pattern Plan

Simultaneous Programmers

•

one system programmer

•

one manager programmer

•

unlimited personal programmers

SMDR Call Storage

200 calls

Special Carrier Access Code

16 digits, 20 entries

Tenant

Time Service Holiday

Verification Code

4 digits, 1000 entries

Verification Code Personal Identification
Number (PIN)

10 digits, 1000 entries

Item

Capacity

Emergency Call

32 digits, 10 entries

Hot Line

32 digits

Key Pad Protocol Dial (ISDN Service Access)

32 digits

Personal Speed Dialling

32 digits, 10 entries/extn.

Summary of Contents for KX-TDA15





































































































































































































































































































































































































































Search results

Summary of Contents for KX-TDA15

Reviews:

Panasonic KX-TDA15, Features Manual, Page: 402 / 420

Search results

Summary of Contents for KX-TDA15

Reviews: