manualshive.com logo in svg

Panasonic KX-TD1232NE, Programming Manual, Page: 92 / 352

Share
Download
Panasonic KX-TD1232NE Programming Manual Download Page 92

2.2

System Programming 

92

General Programming 

[115]

Adjust Time

Description

Note

Available for the KX-TD1232 only.

Used to synchronise the time between the Master and the Slave Systems. Every day at the 
programmed time, system clock and data adjustment are performed between the two systems, 
if available.

Selection

•

Hour: 0 through 23

•

Minute: 00 through 59

Default

1:00

Programming

1.

Enter 115.

Display: Adjust Time

2.

Press NEXT to programme hour.

Display example: 1:00

3.

Enter the hour.

To change the current entry, press CLEAR and the new hour.

4.

Press 

 to programme minute.

5.

Enter the Minute.

To change the current entry, enter the new minute.

6.

Press STORE.

7.

Press END.

Conditions

You cannot leave the entry empty.

Feature References

System Connection

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Reviews:

No comments