Panasonic KX-TD1232NE Programming Manual Download Page 65

Page: 65 / 352

2.1

Manager Programming

General Programming

[019]

Budget Management on TD286 Port

Description

Note

Assigns the charge limitation of a call on a TD286 port basis.

Selection

•

Port number:
KX-TD816 – 01 through 06,
KX-TD1232 – 01 through 12,
( =all ports)

•

Charge limitation (Charge):
0 through 99999999

Default

All ports – 0

Programming

Enter 019.

Display: TD286 Charge Lim.

Press NEXT.

Display example: Port No?

Enter a port number.

To enter port number 01, you can also press NEXT.

Display example: #01: 0

Enter a charge limitation.

To delete the charge limitation, press CLEAR.

Press STORE.

To programme another port, press NEXT or PREV, or SELECT and the desired port
number.

Repeat steps 4 through 6.

Press END.

Conditions

•

If the charge limitation is set "0," no restriction is applied.

•

To assign all ports to the same selection, press the key in step 3. In this case, the display
shows the contents programmed for the first port.

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Search results

Summary of Contents for KX-TD1232NE

Reviews:

Panasonic KX-TD1232NE, Programming Manual, Page: 65 / 352

Search results

Summary of Contents for KX-TD1232NE

Reviews: