Panasonic KX-TD1232NE Programming Manual Download Page 63

Page: 63 / 352

2.1

Manager Programming

General Programming

[018]

TD286 Extension Name Set

Description

Note

Assigns names to the TD286 extension numbers programmed in program [017]

TD286

Extension Number Set.

Selection

•

Port number:
KX-TD816 – 01 through 06
KX-TD1232 – 01 through 12

•

Name:
10 characters (max.)

Default

All ports – Not Stored

Programming

Enter 018.

Display: TD286 EXT Name

Press NEXT.

Display example: Port No?

Enter a port number.

To enter port number 01, you can also press NEXT.

Display: #01:Not Stored

Enter a name.

For entering characters, see Section 1.4

Entering Characters.

To delete the current entry, press CLEAR.

To change the current entry, press CLEAR and enter the new name.

Press STORE.

To programme another port, press NEXT or PREV, or SELECT and the desired port
number.

Repeat steps 4 through 6.

Press END.

Conditions

•

For the KX-TD1232, port number 01 through 06 are for the Master System and 07
through12 are for the Slave, if available.

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Search results

Summary of Contents for KX-TD1232NE

Reviews:

Panasonic KX-TD1232NE, Programming Manual, Page: 63 / 352

Search results

Summary of Contents for KX-TD1232NE

Reviews: