Panasonic KX-TD1232NE Programming Manual Download Page 56

Page: 56 / 352

2.1

Manager Programming

General Programming

[014]

Budget Management on ISDN Port

Description

Assigns the charge limitation of a call on the ISDN port basis.

Selection

•

Port number:
KX-TD816 – 01 through 04,
KX-TD1232 – 03 through 06, 09 through 12,
( =all ports)

•

Charge limitation (Charge):
0 through 99999999

Default

All ports – 0

Programming

Enter 014.

Display: ISDN Charge Lim.

Press NEXT.

Display: Port No?

Enter a port number.

To enter a first port number, you can also press NEXT.

Display example: #03: 0

Enter a charge limitation.

To delete the charge limitation, press CLEAR.

Press STORE.

To programme another port, press NEXT or PREV, or SELECT and the desired port
number.

Repeat steps 4 through 6.

Press END.

Conditions

•

If the charge limitation is set "0," no restriction is applied.

•

To assign all port to one selection, press the key in step 3.
In this case, the display shows the contents programmed for a first port.

•

In case of the KX-TD1232, port numbers 03 through 06 are for the Master System and 09
through 12 are for the Slave, if available.

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Search results

Summary of Contents for KX-TD1232NE

Reviews:

Panasonic KX-TD1232NE, Programming Manual, Page: 56 / 352

Search results

Summary of Contents for KX-TD1232NE

Reviews: