Panasonic KX-TD1232NE Programming Manual Download Page 54

Page: 54 / 352

2.1

Manager Programming

General Programming

[013]

ISDN Extension Name Set

Description

Assigns names to the ISDN extension numbers programmed in program [012]

ISDN

Extension Number Set.

Selection

•

Port number:
KX-TD816 – 01 through 04
KX-TD1232 – 03 through 06, 09 through 12

•

Name:
10 characters (max.)

Default

All ports – Not Stored

Programming

Enter 013.

Display: ISDN EXT Name

Press NEXT.

Display: Port No?->

Enter a port number.

To enter the first port number, you can also press NEXT.

Display: #03:Not Stored

Enter a name.

For entering characters, see Section 1.4

Entering Characters.

To delete the current entry, press CLEAR.

To change the current entry, press CLEAR and the new name.

Press STORE.

To programme another port, press NEXT or PREV, or SELECT and the desired port
number.

Repeat steps 4 through 6.

Press END.

Conditions

•

In case of the KX-TD1232, port numbers 03 through 06 are for the Master System and 09
through 12 are for the Slave, if available.

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Search results

Summary of Contents for KX-TD1232NE

Reviews:

Panasonic KX-TD1232NE, Programming Manual, Page: 54 / 352

Search results

Summary of Contents for KX-TD1232NE

Reviews: