Panasonic KX-TD1232NE Programming Manual Download Page 329

Page: 329 / 352

3.1

DECT Programming

DECT Programming

329

[672]

PS Password Set

Description

Assigns a registration password, which is used for registration (programme [650]

Registration), to each PS.

Selection

•

PS registration number:

KX-TD816 – 01 through 16
KX-TD1232 – 01 through 64

•

PS password: 4 digits

Default

All PSs – 1234

Programming

Enter 672.

Display: PS Password Set

Press NEXT.

Display: PS NO?

Enter the PS registration number.

You can also keep pressing NEXT until the desired PS registration number is displayed.

Display example: PS01:1234

Enter the PS password.

Display example: PS01:5678

Press STORE.

To programme another PS, press NEXT or PREV, or SELECT and the desired PS
registration number.

Repeat steps 4 through 6.

Press END.

Conditions

•

If you modify the PS password, re-register the PS to the system in order to use the password.

Feature References

None

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Search results

Summary of Contents for KX-TD1232NE

Reviews:

Panasonic KX-TD1232NE, Programming Manual, Page: 329 / 352

Search results

Summary of Contents for KX-TD1232NE

Reviews: