manualshive.com logo in svg

Panasonic KX-TD1232NE, Programming Manual, Page: 203 / 352

Share
Download
Panasonic KX-TD1232NE Programming Manual Download Page 203

2.5

CO Line Programming

General Programming 

203

[450]

PRI Configuration

Description

Note

Available for the KX-TD1232 only.

Assigns the maximum number of B channels which are actually used out of the 30 PRI line 
channels and the installation location of BRI card (KX-TD281) or BRI unit (KX-TD280 and 
KX-TD286). The CRC4 mode can be also assigned.

Selection

•

A maximum B channel number and installation spot:

30 Y–NN / 30 N–YN / 30 N–NY / 26 Y–NY /
26 N–YY / 22 Y–YN / 18 Y–YY / 0 YYYY
(Y=the card can be installed, – =this area is not changeable, N=the card is not installed.)

Programming example:

1.

To install TD290 and TD281 to the Master system: 30 Y–NN

2.

To install TD290 to the Master and TD280 to the Slave systems: 30 N–NY

•

CRC4: Disable. / Enable

Default

0YYYY / CRC4 – Enable

Programming

1.

Enter 450.

Display: PRI config.

2.

Press NEXT.

Display example: 0 YYYY

3.

Keep pressing SELECT until the desired combination of the channel number and the card 
status is displayed.

4.

Press STORE.

5.

Press NEXT to assign the CRC4 mode.

Display example:CRC4:Enable

ex.: 30 Y– N N

Status of the expansion area of the slave system.

Status of the basic area of the slave system.

Status of the expansion area of the master system.

Status of the basic area of the master system.

The number of available B channels

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Reviews:

No comments