manualshive.com logo in svg

Panasonic KX-TD1232NE, Programming Manual, Page: 193 / 352

Share
Download
Panasonic KX-TD1232NE Programming Manual Download Page 193

2.5

CO Line Programming

General Programming 

193

[442]

TD286 ISDN Configuration

Description

Assigns the configuration on a TD286 ISDN port basis.

Selection

•

Port number:
KX-TD816 – 01 through 06, 
KX-TD1232 – 01 through 12, 
( =all ports)

•

Point (point to point) / Multipoint (point to multipoint)

Default

All ports – Multipoint

Programming

1.

Enter 442.

Display: TD286 Accs. Mode

2.

Press NEXT.

Display: Port No?

3.

Enter a port number.

To enter port number 01, you can also press NEXT.

Display example: #01:Multipoint

4.

Keep pressing SELECT until the desired selection is displayed.

5.

Press STORE.

6.

To programme another port, press NEXT or PREV, or SELECT and the desired port 
number.

7.

Repeat steps 4 through 6.

8.

Press END.

Conditions

•

For KX-TD1232, port number 01 through 06 are for the Master System and 07 through 12 
are for the Slave, if available.

•

If one equipment is connected to the ISDN port, select "Point." If multiple equipment are 
connected, select "Multipoint."

•

To assign all ports to the same selection, press the   key in step 3. In this case, the display 
shows the contents programmed for the first port.

•

After this assignment, you should reset the system so that this assignment is effective.

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Reviews:

No comments