manualshive.com logo in svg

Panasonic KX-TD1232NE, Programming Manual, Page: 133 / 352

Share
Download
Panasonic KX-TD1232NE Programming Manual Download Page 133

2.3

Timer Programming

General Programming 

133

[208]

Inter Digit Time

Description

Assigns the maximum time allowed between digits on an outgoing toll call. If an extension user 
fails to dial any digits during this time, the DTMF receiver is released. This timer applies until 
the Toll Restriction check is completed.

Selection

Time (seconds): 5 through 30

Default

10 s

Programming

1.

Enter 208.

Display: Inter Digit Time

2.

Press NEXT.

Display example: Time: 10 s

3.

Enter the time.

To change the current entry, press CLEAR and the new time.

4.

Press STORE.

5.

Press END.

Conditions

•

This timer is used for toll restriction checking.

•

You cannot leave the entry empty.

Feature References

Toll Restriction

Summary of Contents for KX-TD1232NE

































































































































































































































































































































































Reviews:

No comments