Panasonic KX-TC1851CB Page 51 Operating Instructions Manual Download

Page: 51 / 56

Useful Information

Before Requesting Help

“

Problem

“

No link to base.

Place on cradle and

try again.

” is displayed

and an alarm tone sounds.

The unit does not work.

Static, sound cuts in/out,
fades. Interference from
other electrical units.

The handset does not ring.

The handset display is
blank.

The handset display is still
blank after pressing

(›)

(‹)

BACK

(fi)

FWD/EDIT

(fl)

Remedy

≥

You are too far from the base unit. Move
closer and try again.

≥

Place the handset on the base unit and
try again.

≥

Plug in the AC adaptor.

≥

Raise the base unit antenna.

≥

Check the settings (p. 10–16).

≥

Charge the battery fully (p. 11).

≥

Clean the charge contacts and charge
again (p. 12).

≥

Install the battery properly (p. 11, 50).

≥

Place the handset on the base unit and
unplug the AC adaptor to reset. Plug in,
and try again.

≥

Locate the handset and the base unit
away from other electrical appliances
(p. 3).

≥

Move closer to the base unit.

≥

Raise the base unit antenna.

≥

Press

(FUNCTION/EXIT/CH)

to select a

clearer channel.

≥

The ringer volume is set to OFF. Set to
HIGH or LOW (p. 19).

≥

If the line is connected to a low voltage
system such as a PBX, the unit may not
ring. Set the line mode to “B” (p. 16).

≥

The handset is in the standby mode
(p. 12). Press

(›)

(‹)

BACK

(fi)

FWD/EDIT

(fl)

to turn the display on.

≥

Charge the battery fully (p. 11).

Summary of Contents for KX-TC1851CB

























































Search results

Summary of Contents for KX-TC1851CB

Reviews:

Related manuals for KX-TC1851CB

Brands by name

Popular brands

Panasonic KX-TC1851CB, Operating Instructions Manual

Search results

Summary of Contents for KX-TC1851CB

Reviews:

Related manuals for KX-TC1851CB

Brands by name

Popular brands