2.00 System Administration
from a Remote Location
Description
From a remote location, you can perform system
programming, diagnosis and traffic
measurements using a Dumb terminal.
For details about communication parameters,
refer to Section 9-D-7.00 “Communication
Interface.”
Conditions
• RMT card (Modem) must be installed in the
system and assign the telephone number of
modem to “Remote Directory Number” (FDN:
3-4 digits) in system programming for
accessing the remote administration feature.
Refer to Section 10-C-4.00 “Operation (OPR)”
for programming.
• For remote access, a data terminal and modem
are required at a remote location.
• Factory programmed 4 types of passwords
from 1st to 4th level for remote administration
are provided.
Passwords are originally factory programmed,
but may be changed at any time. (Refer to
Section 8-F-1.00 “Change Level (CHL),” for
changing password level.)
• You can execute the remote system
administration during on-line communication
mode only.
But when you load the system programming
data from a remote location, the system enters
to off-line communication mode automatically.
Refer to Section 17-B-2.02 “Loading
Procedure” for details.
• Starting up system administration from a
remote location can be done only in Dumb
mode operation.
Operation
Starting up the system administration from a
remote location can be done in the following ways.
• Dial “Remote Directory Number” using Direct
Inward System Access (DISA) feature.
For further information about “Remote Directory
Number,” refer to Section 10-C-4.00 “Operation
(OPR).”
And for further information about DISA feature,
refer to 3-D-2.02 “Direct Inward System Access
(DISA).”
• Program DID feature so that the incoming
telephone number is converted to the “Remote
Directory Number.”
For further information about DID feature, refer to
Section 3-D-2.03 “Direct Inward Dialing (DID).”
• Assign that a call from a remote location can
access the Remote Administration feature
automatically using DIL (1:1) feature.
For further information about DIL (1:1) feature,
refer to Section 3-D-2.01 “Direct In Line (DIL).”
• Remote access with assistance of the operator
The call from a remote location can be made on
any trunk into the system, and be answered by
the operator.
The call is then placed on hold and the Remote
Directory Number of the system dialed is
received.
The operator transfers the call after receiving the
modem answer tone.
The caller at a remote location will then hear the
modem answer tone and can be proceed with
sign-on.
Refer to Section 4-F-1.05 “Unscreened Call
Transfer to Remote” for further information.
When the system administrator at a remote
location accesses the system remote
administration feature, the following message
appears on the display of operator's telephone if
display is provided.
1234:RMT Access
After you log in to the system from a remote
location, you can operate the system in the same
way as if you were on-site.
Only one system administration terminal can
access the system at a time.
15-B-2
Summary of Contents for KX-T336
