Panasonic KX-PRX120W Service Manual Download Page 25

Page: 25 / 89

KX-PRX120W/KX-PRXA10W

9.1.1.2.

Check Power (Handset)

Does not power on

Is the voltage of the battery
3.7V or under?

Re-charge the battery

Cleaning the

battery

terminal.

Did the problem fix?

YES

Update software.
Did the problem fix?

Replace with a new circuit board

YES

Replace with a

fully charged

battery.

Did the problem fix?

YES

End

YES

Is the voltage of the battery
3.7V or under?

Is the current value

500mA or under?

(Use Power Supply.

Read the displayed current

of Power Supply)

YES

Did the problem fix?

YES

End

YES

End

Battery is not charged

Cleaning the charge terminal
of both handset and charger.
Did the problem fix?

Which charge is not working,

Charger or USB port of handset(*1)?

Charger

Update software.

Did the problem fix?

YES

End

Replace with a new circuit board

End

Replace with a new AC Adaptor.
Did the problem fix?

YES

End

Update software.
Did the problem fix?

YES

End

Replace with a new charger.
Did the problem fix?

Replace with a new circuit board

End

YES

Replace with a new battery.

Battery is chargerd?

YES

End

USB

YES

(*1) for KX-PRX150 and PRXA15 only

Summary of Contents for KX-PRX120W


























































































Search results

Summary of Contents for KX-PRX120W

Reviews:

Related manuals for KX-PRX120W

Brands by name

Popular brands

Panasonic KX-PRX120W, Service Manual

Search results

Summary of Contents for KX-PRX120W

Reviews:

Related manuals for KX-PRX120W

Brands by name

Popular brands