Panasonic KX-MB2085CXW Service Manual Download Page 5 | Manualshive

Page: 5 / 276

background image

5

KX-MB2085CXW/KX-MB2090CXW

1 Safety Precautions

1. Before servicing, unplug the AC power cord to prevent an electric shock.
2. When replacing parts, use only the manufacturer's recommended components.
3. Check the condition of the power cord. Replace if wear or damage is evident.
4. After servicing, be sure to restore the lead dress, insulation barriers, insulation papers, shields, etc.
5. Before returning the serviced equipment to the customer, be sure to perform the following insulation resistance test to prevent

the customer from being exposed to shock hazards.

1.1.

For Service Technicians

•

Repair service shall be provided in accordance with repair technology information such as service manual so as to pre-
vent fires, injury or electric shock, which can be caused by improper repair work.

1. When repair services are provided, neither the products nor their parts or members shall be remodeled.
2. If a lead wire assembly is supplied as a repair part, the lead wire assembly shall be replaced.
3. FASTON terminals shall be plugged straight in and unplugged straight out.

•

ICs and LSIs are vulnerable to static electricity.
When repairing, the following precautions will help prevent recurring malfunctions.

1. Cover the plastic part's boxes with aluminum foil.
2. Ground the soldering irons.
3. Use a conductive mat on the worktable.
4. Do not touch the IC or LSI pins with bare fingers.

1.2.

AC Caution

For safety, before closing the lower cabinet, please make sure of the following precautions.

1. The earth lead is fixed with the screw.
2. The AC connector is connected properly.

«
...
3
4
5
6
7
...
»

Summary of Contents for KX-MB2085CXW





















































































































































































































































































Reviews:

No comments

Related manuals for KX-MB2085CXW

Brand: Canon Pages: 86

Brand: Canon Pages: 20

Brand: Samsung Pages: 347

SCX 6555N - MultiXpress Mono Multifunction

Brand: Samsung Pages: 180

SCX-4300 - SCX 4300 B/W Laser

Brand: Samsung Pages: 18

SCX-4521FG - B/W Laser - All-in-One

Brand: Samsung Pages: 215

SCX 6320F - B/W Laser - All-in-One

Brand: Samsung Pages: 332

SCX 4828FN - Laser Multi-Function Printer

Brand: Samsung Pages: 248

SCX 4725FN - B/W Laser - All-in-One

Brand: Samsung Pages: 253

ML 2851ND - B/W Laser Printer

Brand: Samsung Pages: 179

ML 2510 - B/W Laser Printer

Brand: Samsung Pages: 84

ML 1740 - B/W Laser Printer

Brand: Samsung Pages: 152

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 142

ML 1630 - B/W Laser Printer

Brand: Samsung Pages: 82

Brand: Samsung Pages: 2

Brand: Samsung Pages: 384

Lazett Combo SCX-4216F

Brand: Samsung Pages: 135

Brand: Samsung Pages: 414

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands