Feature/Code
Selection
Setting the IP address
automatically for the LAN
connection
MBNM
5
NM
3
NM
3
N
This feature will be displayed only when feature #500 is activated.
M
0
N
“
DISABLED
”
(default): Deactivates this feature.
M
1
N
“
ENABLED
”
: IP address will be allocated automatically without using a
DHCP (Dynamic Host Configuration Protocol) server.
Setting HTTPD for the LAN
connection
MBNM
5
NM
3
NM
4
N
M
0
N
“
DISABLED
”
: Denies access to the web server.
M
1
N
“
ENABLED
”
(default): Allows access to the web server.
IPv6 protocol
MBNM
5
NM
3
NM
5
N
M
0
N
“
DISABLED
”
(default): Deactivates this feature.
M
1
N
“
ENABLED
”
: IPv6 protocol can be used. After installing the printer driver,
be sure to change the port to IPv6 protocol. You can check the IPv6 protocol
address by printing the
“
SETUP LIST
”
Note:
R
To activate this feature, you need to turn the power switch of the unit OFF,
then ON.
Setting the primary WINS
server for the LAN
connection
MBNM
5
NM
3
NM
8
N
This feature is available when feature #500 is deactivated.
1.
M
MENU
N
A
MBNM
5
NM
3
NM
8
N
A
M
SET
N
2.
Enter the primary WINS server of the network on the LAN using the dial
keypad.
A
M
SET
N
A
M
MENU
N
Setting the secondary WINS
server for the LAN
connection
MBNM
5
NM
3
NM
9
N
This feature is available when feature #500 is deactivated.
1.
M
MENU
N
A
MBNM
5
NM
3
NM
9
N
A
M
SET
N
2.
Enter the secondary WINS server of the network on the LAN using the dial
keypad.
A
M
SET
N
A
M
MENU
N
Erasing all email addresses,
FTP destinations, and SMB
folder destinations stored in
the unit
MBNM
5
NM
7
NM
8
N
M
0
N
“
NO
”
(default)
M
1
N
“
YES
”
R
Disconnect the telephone line cord, USB cable and LAN cable before
activating this feature.
To erase all email addresses:
1.
M
MENU
N
A
MBNM
5
NM
7
NM
8
N
2.
Press
M
1
N
to select
“
YES
”
.
A
M
SET
N
3.
Press
M
1
N
to select
“
YES
”
.
A
M
SET
N
A
M
MENU
N
To erase FTP destinations:
1.
M
MENU
N
A
MBNM
5
NM
7
NM
8
N
2.
Press
M
1
N
to select
“
YES
”
.
A
M
SET
N
3.
Press
M
0
N
to select
“
NO
”
.
A
M
SET
N
4.
Press
M
1
N
to select
“
YES
”
.
A
M
SET
N
A
M
MENU
N
To erase SMB folder destinations:
1.
M
MENU
N
A
MBNM
5
NM
7
NM
8
N
2.
Press
M
1
N
to select
“
YES
”
.
A
M
SET
N
3.
Press
M
0
N
to select
“
NO
”
.
A
M
SET
N
4.
Press
M
0
N
to select
“
NO
”
.
A
M
SET
N
5.
Press
M
1
N
to select
“
YES
”
.
A
M
SET
N
A
M
MENU
N
70
9. Programmable Features
Summary of Contents for KX-MB2085CX
Page 121: ...Z Zoom hold Feature 468 66 121 15 Index ...
Page 122: ...122 Notes ...
Page 123: ...123 Notes ...