Panasonic KX-HDV230 Page 22 Administrator'S Manual Download | Manualshive

Page: 22 / 342

background image

1.1 Setup

1.1.1 Factory Defaults

Many of the settings for this unit have been configured before the unit ships.
Where possible, these settings are configured with the optimum or most common values for the setting. For
example, the port number of the SIP (Session Initiation Protocol) server is set to "5060".
However, many of the settings, such as the address of the SIP server or the phone number, have not been
pre-configured, and they must be modified depending on the usage environment. If the port number of the SIP
server is not "5060", the value of this setting must be changed.
This unit thus will not function properly using only the factory default settings. The settings for each feature
must be configured according to the environment in which the unit is used.

1.1.2 Language Selection for the Unit

You can change the language used on the LCD.
In addition, various settings can be configured by accessing the Web user interface from a PC on the same
network (

®

Section 4 Web User Interface Programming

). You can select the language for the Web

user interface.

Note

•

To select the display language for the unit, refer to the Operating Instructions on the Panasonic Web
site (

®

Introduction

•

To select the display language for the Web user interface, see

4.4.1 Language Settings

.

1.1.3 Basic Network Setup

This section describes the basic network settings that you must configure before you can use the unit on your
network.
You must configure the following network settings:

•

IP Address Mode (IPv4 or IPv6 or IPv4/IPv6 Dual) settings

•

TCP/IP settings (DHCP / RA for IPv6 / static IP)

•

DNS server settings

For details about basic network settings via the Web user interface, see

4.3.1 Basic Network Settings

.

TCP/IP Settings for IPv4 (DHCP or Static IP Address Assignment)

A unique IP address must be assigned to the unit so that it can communicate on the network. How you assign
an IP address depends on your network environment. This unit supports the following 2 methods for assigning
an IP address:

Obtaining an IP Address Automatically from a DHCP Server

You can configure the unit to automatically obtain its IP address when it starts up from a DHCP server running
on your network. With this method, the system can efficiently manage a limited number of IP addresses. Note
that the IP address assigned to the unit may vary every time the unit is started up.
For details about the DHCP server, consult your network administrator.

22

Administrator Guide

Document Version 2015-07

1.1.3 Basic Network Setup

«
...
20
21
22
23
24
...
»

Summary of Contents for KX-HDV230























































































































































































































































































































































Reviews:

No comments

Related manuals for KX-HDV230

Brand: Yealink Pages: 8

Brand: T-Mobile Pages: 2

Brand: Patton electronics Pages: 79

Brand: O2 Pages: 36

Brand: MWg Pages: 60

Brand: HTC Pages: 26

Brand: JETHRO Pages: 66

Brand: X-View Pages: 42

Brand: QUO Pages: 28

Brand: iBall Pages: 80

Brand: Pantech Pages: 76

Brand: AMGOO Pages: 32

Brand: Telme Pages: 102

Brand: Xiaomi Pages: 1

Brand: Myria Pages: 74

Brand: GENERAL MOBILE Pages: 16

Brand: Acer Pages: 91

Brand: Acer Pages: 96

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands