Panasonic KX-FT932RU-B, Service Manual

Page: 54 / 177

54
KX-FT932RU-B/KX-FT932CA-B/KX-FT932UA-B/KX-FT934RU-B/KX-FT934CA-B/KX-FT934UA-B
10 Test Mode
The codes listed below can be used to perform simple checks for some of the unit’s functions. When complaints are received
from customers, they provide an effective tool for identifying the locations and causes of malfunctions. To do this, you set the
Service mode (Refer to
Operation Flow (P.56).) first, then operate the below test items.
Note:
The numbers in the boxes (XXX) indicate the keys to be
input for the various test modes.
Test Mode Type of Mode Code Function
Operation after code
input
FACTORY SET Service Mode “5” “5” “0” Refer to Memory Clear Specification (P.59).
SET
FLASH MEMORY
CHECK Service Mode “5” “5” “1” Indicates the version and checks the sum of the FLASH MEMORY.
SET
DTMF SINGLE TEST Service Mode “5” “5” “2” Outputs the DTMF as single tones. Used to check the frequencies of the individ-
ual DTMF tones. Refer to
Service Function Table (P.57).
1....ON
2....OFF
MODEM TEST Service Mode “5” “5” “4” Telephone line circuit is connected automatically, output the following signals on
the circuit line.
1) OFF 2) 9600bps 3) 7200bps 4) 4800bps 5) 2400bps 6) 300bps 7) 2100Hz
8) 1100Hz
SET
SCAN CHECK Service Mode “5” “5” “5” Turns on the LEDs of the CIS and operates the read systems.
Refer to
CIS (Contact Image Sensor) Section (P.115).
SET
MOTOR TEST Service Mode “5” “5” “6” Rotates the transmission and reception motor to check the operation of the motor.
12: FAX TX / Reading memory
52: Recording paper is fed
22: Copy
34: Cutter
44: Recording Paper reverse
Press [STOP] button to quit.
SET
LED CHECK Service Mode “5” “5” “7” All LEDs above the operation panel board flash on and off, or are illuminated.
SET
LCD CHECK Service Mode “5” “5” “8” Checks the LCD indication.
Illuminates all the dots to check if they are normal.
Refer to
Operation Panel Section (P.113).
SET
KEY CHECK Service Mode “5” “6” “1” Checks the button operation.
Indicates the button code on the LCD while the button is pressed. Refer to
But-
ton Code Table (P.55).
Refer to Operation Panel Section (P.113).
START (any key)
MEMORY CLEAR
(except History data) Service Mode “7” “1” “0” Refer to Memory Clear Specification (P.59).
START
SENSOR CHECK Service Mode “8” “1” “5” If you enter this mode and operate sensor levers with your hands, the LCD dis-
play of the related sensor (or switch) turns ON / OFF. Also, when copying a doc-
ument, the related sensor will turn ON / OFF.
For each sensor’s operation, refer to
Sensors and Switches (P.26).
Do Sn Co Jm Ct : LCD DISPLAY
Do: Document set sensor
:Paper inserted. Turns on when a document is inserted.
Sn: Read position sensor.
:At the read position, turns on when the front cover is opened and the sensor
lever is pressed directory.
Co: Cover open sensor
:Turns on and off when the front cover is opened and closed.
Jm: JAM sensor
:When JAM sensor is on “Jm” functions.
Ct: Cutter sensor
:When cutter sensor is on “Ct” functions.
SET
PRINT TEST PAT-
TERN Service Mode “8” “5” “2” Prints out the test pattern.
Used mainly at the factory to test the print quality.
You can select 1~4. (See
Print Test Pattern (P.55))
SET