Panasonic KX-FPC91, Service Manual

Page: 101 / 247

2.4.4. SERVICE FUNCTION TABLE
Code Function Set Value Effective
Range
Default Remarks
501 Pause time set X 100 msec 001~600 50 ----------
502 Flash time X 10 ms 01~99 70 ----------
503 Dial speed select 1:10 pps 2:20
pps 1, 2 1 ----------
511 VOX sense 1:High 2:Low 1, 2 1 When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected on
the telephone line, change this setting to "LOW".
520 CED frequency select 1:2100 Hz
2:1100 Hz 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in 2.3.5.1.5 THE
UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS(P.56).
521 International mode select 1:ON 2:OFF 1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in 2.3.5.1.5 THE
UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS(P.56).
522 Auto standby select 1:ON 2:OFF 1, 2 1 The resolution reverts to the default when
transmission is complete.
523 Receive equalizer select 1:0km 2:1.8km
3:3.6km
4:7.2km 1~4 1 When the telephone station is far from the unit or
reception cannot be performed correctly, adjust
accordingly.
524 Transmission equalizer select 1:0km 2:1.8km
3:3.6km
4:7.2km 1~4 1 When the telephone station is far from the unit or
transmission cannot be performed correctly, adjust
accordingly.
550 Memory clear: To reset the value to the default one, except the top margin
(853) and left margin (854). "START" input
551 ROM check See 2.5 TEST FUNCTIONS(P.113).
552 DTMF single tone test 1:ON 2:OFF 1, 2 2 See 2.5 TEST FUNCTIONS(P.113).
553 Monitor on FAX communication
select 1:OFF
2:PHASE B
3:ALL 1~3 1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
554 Modem test See 2.5 TEST FUNCTIONS(P.113).
555 Scan test See 2.5 TEST FUNCTIONS(P.113).
556 Motor test 0 See 2.5 TEST FUNCTIONS(P.113).
557 LED test See 2.5 TEST FUNCTIONS(P.113).
558 LCD test See 2.5 TEST FUNCTIONS(P.113).
559 Document jam detection select 1:ON 2:OFF 1, 2 1 See 2.2.1 DOCUMENT JAMS(P.33).
561 KEY test See 2.5 TEST FUNCTIONS(P.113).
570 BREAK % select 1:61% 2:67% 1, 2 1 Sets the % break of pulse dialing according PBX.
571 ITS auto redial time set X number of
times 00~99 0 Selects the number of times that ITS is redialed
(not including the first dial).
572 ITS auto redial line disconnection
time set X second 001~999 30 Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of
rings 01~99 15 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
590 FAX auto redial time set X number of
times 00~99 2 Selects the number of redial times during FAX
communication (not including the first dial).
591 FAX auto redial time disconnection
time set X second 001~999 45 Sets the FAX redial interval during FAX
communication.
592 CNG transmit select 1:OFF
2:ALL
3:AUTO 1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG id output only when automatic dialing
is performed. OFF: CNG id not output at phase A.
Refer to 2.3.5.1.2 SOMETIME THERE IS A
TRANSMIT PROBLEM(P.54).
593 Time between CED and 300bps 1:75 msec
2:500 msec
3:1 sec 1~3 1 See Symptom/Countermeasure Table for long
distance and international calls in 2.3.5.1.5 THE
UNIT CAN COPY, BUT CANNOT EITHER
TRANSMIT/RECEIVE LONG DISTANCE OR
INTERNATIONL COMMUNICATIONS(P.56).
Refer to 2.3.5.1.3 RECEIVE PROBLEM(P.55) and
2.3.5.1.5 THE UNIT CAN COPY, BUT CANNOT
EITHER TRANSMIT/RECEIVE LONG DISTANCE
OR INTERNATIONL COMMUNICATIONS(P.56).
101
KX-FPC91