Panasonic KX-FP105BX, Service Manual

Page: 11 / 238

11
(Model KX-FP105BX/KX-FP105CX)
KX-FP105BX/KX-FP105CX
2.4. SERVICE FUNCTION TABLE (Change from original page 87)
Code Function Set Value Ef fective Range Def ault Remarks
501 Pause time set X 100 msec 001~600 50
502 Flash tim e set X 10 m sec 01~99 70
503 Dial speed select 1:10 pps 2:20 pps 1, 2 1
511 Vox sense 1:High 2:Low 1, 2 1
When the TAM (or EXT TAM) does not stop
recording the ICM because noise is detected
on the telephone line, change this setting to
"LOW".
520 CED frequency select 1:2100 Hz 2:1100 Hz 1, 2 1
See Sym ptom /Counterm easure Table
for long distance and international calls in
2.3.3.1. Defective Facsim ile Section.
521 International mode select 1:ON 2:OFF 1, 2 1
See Sym ptom /Counterm easure Table
for long distance and international calls in
2.3.3.1. Defective Facsim ile Section.
522 Def ault mode select 1:ON 2:OFF 1, 2 1
The resolution reverts to the default w hen
transmission is complete.
523 Receive equalizer select 1:ON 2:OFF 1, 2 2
When the telephone station is far from the
unit or reception cannot be perf ormed
correctly, adjust accordingly.
550
"START" input
552 DTMF single tone test 1:ON 2:OFF 1, 2 2
See 2.5. TEST FUNCTIONS.
553 Monitor on FAX communication select
1: OFF
2:PHASE B
3:ALL
1~3 1
554 Modem test
See 2.5. TEST FUNCTIONS.
555 Scan check
See 2.5. TEST FUNCTIONS.
556 Motor test 0
See 2.5. TEST FUNCTIONS.
557 LED test
See 2.5. TEST FUNCTIONS.
558 LCD test
See 2.5. TEST FUNCTIONS.
559 Document jam detection select 1:ON 2:OFF 1, 2 1
See 2.2.1. Paper Jam .
561 KEY test
See 2.5. TEST FUNCTIONS.
570 BREAK % select 1:61% 2:67% 1, 2 1
Sets the % break of pulse dialing according
PBX.
571 ITS auto redial time set X number of times 00~99 14
Selects the number of times that ITS is
redialed (not including the first dial).
572 ITS auto redial line disconnection time set X second 001~999 30
Sets the interval of ITS redialing.
573 Remote turn-on ring number set X number of rings 01~99 15
Sets the number of rings bef ore the unit
starts to receive a document in the TEL
mode.
590 FAX auto redial time set X number of times 00~99 5
Selects the number of redial times during
FAX communication (not including the first
dial).
591 FAX auto redial time disconnection time set X second 001~999 45
Sets the FAX redial interval during FAX
communication.
592 CNG transmit select
1: OFF
2:ALL
3:AUTO
1~3 2
Lets you select the CNG output during FAX
transmission.
ALL: CNG is output at phase A.
AUTO: CNG is output only w hen automatic
dialing is performed.
OFF: CNG is not output at phase A.
593 Time betw een CED and 300bps
1: 75 msec 2:500 msec
3:1 sec
1~3 1
See Sym ptom /Counterm easure Table
for long distance and international calls in
2.3.3.1. Defective Facsim ile Section.
594 Overseas DIS detection select
1:detects at the 1st time
2:detects at the 2st time
1, 2 1
See Sym ptom /Counterm easure Table
for long distance and international calls in
2.3.3.1. Defective Facsim ile Section.
595 Receive error limit value set X Number of times 001~999 100
Sets the number of acceptable error lines
w hen the FAX reconstructs the received
data.
Memory clear: To reset the value to the def ault one, except the top margin (853) and left margin (854).