background image

Available number of characters:

 1 - 32 characters

Unavailable characters:

 " & * / : ; < > ? \ |

[FTP transmission retry]

Select “On” or “Off” to determine whether or not to resend failed FTP transmissions.

On:

 If transmission fails, transmissions are resent until they are successfully sent.

Off:

 If transmission fails, the image that failed to be sent is discarded and the next image is sent.

Default:

 Off

[Pre alarm]

Transmission interval

Select the update interval of images before an alarm occurs from the following.
0.1fps/ 0.2fps/ 0.33fps/ 0.5fps/ 1fps

Default:

 1fps

Maximum number of images

Select the number of images to be transmitted from the following.
0pics/ 1pic/ 2pics/ 3pics/ 4pics/ 5pics/ 6pics*/ 7pics*/ 8pics*/ 9pics*/ 10pics*/ 20pics*/ 30pics*/ 40pics*/
50pics*

Default:

 0 pics

Recording duration

The recording duration, which changes according to the configured “Transmission interval” and “Maximum
number of images”, of images recorded before an alarm occurs is displayed.

Note

When “JPEG(1)” is selected for the capture size of the image to be transmitted, pre alarm is unavailable
if the image capture size of “JPEG(1)” is “1920x1080”.

When “On” is selected for “Image compression rate upon alarm detection”, only post alarm recorded
images are compressed. Compression is not applied to pre alarm recorded images.

When a selection with an asterisk (*) on the right of it is selected for “Maximum number of images” of
“Pre alarm”, the specified number of images may not be able to be sent depending on the image capture
size and image quality. The following table shows the maximum number of images that can be sent
for pre alarm.

 

Image quality

0

1

2

3

4

5

6

7

8

9

Image
capture
size

1280x960

5

6

7

8

10

10

10

20

30

40

1280x720

7

8

10

10

10

20

20

30

40

50

800x600

9

10

10

20

20

30

30

50

50

50

VGA

10

20

20

30

30

40

50

50

50

50

640x360

20

30

40

50

50

50

50

50

50

50

400x300

30

30

40

50

50

50

50

50

50

50

QVGA

40

50

50

50

50

50

50

50

50

50

320x180

50

50

50

50

50

50

50

50

50

50

160x120

50

50

50

50

50

50

50

50

50

50

160x90

50

50

50

50

50

50

50

50

50

50

Operating Instructions

135

12 Configuring the network settings [Network]

Summary of Contents for IDEHAL WV-SUD638PJ



















































































































































































































Reviews: