Panasonic GM1 Series Reference Manual Download Page 20

Page: 20 / 98

3.1 Connecting Analog Input

3.1.1 Precautions When Connecting Analog Signal

● Use double-core twisted-pair shielded wires for connecting analog signals.
● Connect the shield of the shielded cable to the ground on the load device side.

However, depending on the conditions of the external noise, it may be better to ground
externally or not to ground the shield.

● Do not have the analog input wiring close to AC wires, power wires, or load line from a

device other than the Motion Controller. Also, do not bundle it with them.

● The NC terminals on the terminal block are unused. Do not use these terminals to relay

wires because the terminals include those connected internally.

3.1.2 Terminal Layout Diagram of the GM1 Analog Input Unit

The terminal used by the analog voltage input is common to that used by the analog current

input.

VI0

VI1

VI2

VI3

COM

CH0

CH1

CH2

CH3

CN1

VI4

VI5

VI6

VI7

COM

CH4

CH5

CH6

CH7

CN2

3.1.3 Analog Input Circuit and Wiring

This section describes the input circuit and wiring of the analog input unit. The circuit for the

voltage input is the same as that for the current input.

3.1 Connecting Analog Input

3-2

WUME-GM1AIO-01

Summary of Contents for GM1 Series



































































































Search results

Summary of Contents for GM1 Series

Reviews:

Related manuals for GM1 Series

Brands by name

Popular brands

Panasonic GM1 Series, Reference Manual

Search results

Summary of Contents for GM1 Series

Reviews:

Related manuals for GM1 Series

Brands by name

Popular brands