manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 287

285

9 Security

  9.2.2 802.1X Forced Authorized MAC Settings    

9.2.2

802.1X Forced Authorized MAC Settings 

                   Use the following window to implement the settings on IEEE 802.1X 

                   forced authorized MAC and display its settings.

                     Choose 

Security > 802.1X > 802.1X Forced Authorized MAC Settings

 to 

                   display the following window. 

Figure 9-5 802.1X Forced Authorized MAC Settings

                    In the section of

 Forced Authorized MAC Settings

, you can configure 

                    the following parameters. 

                    Click 

Apply

 to add a new entry.

                    Click 

Find

 to search and display the entries based on the search condition 

                    specified.

                    Click 

Delete

 to delete the entry specified. 

                    If two or more pages exist, enter the page numbers. Then click 

Go

 to 

                    move to a specific page.

 

Parameter

Overview

From Port/ To Port

Choose the port you use.

MAC Address

Enter a MAC address of supplicant.

Mask Length

Enter the MAC mask bit-length. The range is from 0 to 
48. 

Authentication Status

Choose the authentication status. The options available 
are as follows.

•

Authorized

 - Choose this option to force the 

authorized status. 

•

Unauthorized

 - Choose this to force the 

unauthorized status.

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands