Panasonic FV-SW20VEC1 Installation And Operating Instructions Manual Download Page 10

Page: 10 / 10

TROUBLESHOOTING

Fault code

Problem

Action

F10

OA temperature sensor error

Please disconnect the power and contact the dealer

for repair

F11

OA humidity sensor error

Please disconnect the power and contact the dealer

for repair

F12/F13

RA temperature and humidity

Please disconnect the power and contact the dealer

sensor error

for repair

F20

SA motor error

Please disconnect the power and contact the dealer

for repair

F21

EA motor error

Please disconnect the power and contact the dealer

for repair

F30

OA damper error

Please disconnect the power and contact the dealer

for repair

F31

EA damper error

Please disconnect the power and contact the dealer

for repair

F32

Center damper error

Please disconnect the power and contact the dealer

for repair

SPECIFICATIONS

PRODUCT SERVICE

Warning Concerning Removal of Covers.

The unit should be serviced qualified technicians only.

Your product is designed

manufactured to ensure a minimum of maintenance.

Should your unit require service or parts, call Panasonic Call Center at 1-866-292-7299 (USA)

or 1-800-669-5165 (Canada).

Panasonic Corporation of North America

Two Riverfront Plaza, Newark, NJ 07102

www.panason1c.com

Panasonic Canada Inc.

5770 Ambler Drive, Mississauga, Ontario L4W 2T3

www.panason1c.com

Printed in China

Issue date:07 /2021

P0421-1071 SW20VE 153A

Summary of Contents for FV-SW20VEC1











Search results

Summary of Contents for FV-SW20VEC1

Reviews:

Related manuals for FV-SW20VEC1

Brands by name

Popular brands

Panasonic FV-SW20VEC1, Installation And Operating Instructions Manual

Search results

Summary of Contents for FV-SW20VEC1

Reviews:

Related manuals for FV-SW20VEC1

Brands by name

Popular brands