Panasonic FV-08VSL3 User Manual Download Page 3

Canada  only:  Not  to  be  installed  in  a  ceiling  thermally  insulated  to  a  value  greater  than  R40.

Install  the  fan  at  least  1.5m  (5  feet)  above  the  floor,  and  the  fan  must  be  installed  above 
a  counter  or  major  appliances  that  serves  as  a  barrier. 

Ceiling  joist  or  wall  stud  must  be  subjected  to  static  load  more  than  five  times  the  weight  of 
the  product.

This  product  must  be  properly  grounded.

Do  not  install  this  ventilating  fan  where  interior  room  temperature  may 
exceed  104°F  (40°C).

Make  sure  that  the  electric  service  supply  voltage  is AC  120V,  60  Hz.

Follow  all  local  electrical  and  safety  codes,  as  well  as  the  National 
Electrical  Code  (NEC)  and  the  Occupation  Safety  and  Health Act  (OSHA).

Always  disconnect  the  power  source  before  working  on  or  near  the  fan, 
motor,  light  fixture  or  junction  box. 

Protect  the  supply  wiring  from  sharp  edges,  oil,  grease,  hot  surfaces,
chemicals  or  other  objects.

Do  not  kink  the  supply  wiring.

Provide  make  up  air  for  proper  ventilation.

For  general  ventilating  use  only.  Do  not  use  to  exhaust  hazardous  or 
explosive  materials  and  vapors.

Not  for  use  in  cooking  area.  (Fig.B)

The  special-purpose  or  dedicated  parts,  such  as  mounting
fixtures,  must  be  used  if  such  parts  are  provided.

3

Do  not  install  the  unit  where  ducts  are  configured  as  shown 
in  Fig.A.

Do  not  install  with  a  method  which  is  not  approved  in  the  instructions.

Adaptor

USA only: This product has a fluorescent lamp that contains mercury. Disposal may be 
regulated in your community due to environmental considerations. For disposal or 
recycling information, please contact your local authorities or visit Panasonic website: 
http://www.panasonic.com/environmental or call 1-888-769-0149.
 
 

CAUTION

A  statement  to  the  effect  that  when  the  product  is  to  no  longer  be  used,  it  must  not  be  left 
in  place  but  removed,  to  prevent  it  from  possible  falling.

WARNING

Do  not  use  this  fan  with  any  solid-state  speed  control  device.  Solid  state  controls  may  cause
harmonic  distortion  which  can  cause  motor  humming  noise.

Summary of Contents for FV-08VSL3













Reviews: