Panasonic FP2 Positioning Unit RTEX Technical Manual Download Page 130 | Manualshive

Page: 130 / 288

background image

8-28

8.3

53B

Synchronous Operation

8.3.1

128B

Overview of Synchronous Operation

The synchronous operation is a function to set an axis to be the standard (master axis) and an axis to be
synchronized (slave axis), and make the operations the master and slave axes identical (synchronous).

The features of the synchronous operation are as below.

-

A maximum of 2 groups can be set for the synchronous operation.

-

The master and slave axis can be set for one axis each.)

Two types of synchronous operation can be selected.

1. Synchronous mode A

Using this mode enables to switch the setting of the synchronous operation between “enabled” and
“disabled”, and perform the synchronous operation as necessary.

2. Synchronous mode B

This mode is used to drive a large-sized table such as a carrier machine with two motors. The
synchronous operation cannot be disabled in the mode B..

Differences in the operations of synchronous modes

Synchronous mode A

Synchronous mode B

Synchronous

setting

A maximum of 2 groups can be set for the synchronous group.

An individual operation mode can be set for each synchronous group.

Enabled/disabled

of synchronous

operation

It can be selected either Enabled or Disabled.

Only Enabled

Positioning

operation

JOG operation

Operation stop

Pulser operation

【

Synchronous: When enabled

】

Operates with the setting of the master axis.

The positioning starts for the master axis.

Operates with the setting of the master axis.

The positioning starts for the master axis.

【

Synchronous: When disabled

】

The master and slave axes are operated

according to the respective settings for each axis.

The positioning starts for each axis.

Home return

It is performed for each axis.

It is necessary to set the synchronous operation

to be “Disabled” when performing the home

return.

Some home return methods cannot be used.

The connection of the switch of the

positioning unit may be changed according

to the home return methods.

«
...
128
129
130
131
132
...
»

Summary of Contents for FP2 Positioning Unit RTEX

































































































































































































































































































Reviews:

No comments

Related manuals for FP2 Positioning Unit RTEX

Brand: Jafar Pages: 9

Brand: NEJE Pages: 17

Brand: Oceanic Pages: 13

Brand: TCS Basys Controls Pages: 2

Brand: rada Pages: 16

Brand: Eaton Pages: 6

Brand: Eaton Pages: 35

Brand: Eaton Pages: 18

Brand: Eaton Pages: 73

Brand: Eaton Pages: 4

Cutler-Hammer IQ DP-4000

Brand: Eaton Pages: 87

Brand: Eaton Pages: 14

Brand: Eaton Pages: 36

Brand: Jabra Pages: 3

Brand: Samson Pages: 56

Brand: EasyIO Pages: 17

1E0671-1 MCR2.9

Brand: Haberl Electronic Pages: 9

Brand: J+J Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands